Truck Explorer - VEI
Vehicle Explorer Interface


Buy VEI   

Shopping Cart

Cart is empty

Software v6.19 version (Stable)


Truck Explorer v6.19 (build 16503) STABLE release (2022-04-08)

What's new:
  1. SCANIA faults read/erase (free)
  2. SCANIA keys info read (free)
  3. SCANIA EMS speed limit (price 40 tokens)
  4. CPC4 "Restore RTC" action (price 10 tokens). Remove fault code: 61020C; 10A10.
  5. CPC3 memory operation via OBD (License MB CPC3 OBD)
  6. CPC3Evo memory operation via DC (License MB CPC3Evo DC)
  7. CPC3Evo memory operation via OBD (License MB CPC3Evo OBD)
  8. CPC3Evo password reset (price 10 tokens)
  9. CPC3Evo speed limit (change after password reset) (License CPC3 EXTRA updated)
  10. DDDL Backdoor password calculator (price 10 tokens)
  11. MAN EDC17CV42 + PTM pairing by OBD (price 100 tokens)
  12. MAN EDC17CV42 memory operations via GPT (License MAN EDC17CV42 GPT)
  13. MAN EDC17CV42 parameters change (tester info, item number, data record number, software number, unmachined part number, VIN, EOL info) uses tokens (5 tokens each).
  14. IVECO EDC17CV41 memory operations via GPT (License IVECO  EDC17CV41 GPT)
  15. IVECO VCM2 / VCM3 speed limit OBD/DC (price 20 tokens)
  16. IVECO VCM2 / VCM3 parameters (VIN, PIC) read/write via OBD or DC (price 5 tokens)
  17. Volvo EDC7UC31 memory operations via OBD/DC/GPT (use "ECU" connection)
  18. ACM3 connection info and parameters via OBD  (torque limit, VIN)
  19. MR unit pump ("trim") codes (price 2 tokens)
  20. IVECO faults codes operations (read/erase). License no needed
  21. "Read device info" shows info about DC & JTAG if connected
  22. During JTAG/BDM connect check is MCU powered on
  23. EDC17CV41 checksum check and correct before FLASH write
  24. EDC17CV42 checksum check and correct before FLASH write
  25. MCM keys information now handles FBS4 system type correctly (was "unavailable function" error)
  26. MAN EDC7C3 BDM memory operations (needs EDC7 BDM license)
  27. Mercedes (Wabco) EBS3/EBS4 memory operations via DC (License MB EBS DC)
  28. Mercedes (Wabco) EBS3/EBS4 memory operations via OBD (License MB EBS OBD)
  29. Show FBS4 immo status (paired/not paired) for MCM2.1
  30. Use full ECU name ("MCM21" instead "MCM", "EDC7C32" instead "EDC7" etc) in suggested filename when saving dump (done for ACM/MCM/VCM/CPC3/EDC7)
  31. During memory operations we show type of FLASH (internal or external)
  32. If ECU has only 1 EEPROM, we show simple "EEPROM" not "EEPROM A" during memory operations & in suggested filename when saving dump
  33. Aded JTAG HW2 support
  34. Mercedes fault descriptions updated (from Xentry 2021.09; before was 2019.05)
  35. MR "Write fuel map" operation was removed (use "Write FLASH" instead)
What's fixed:
  1. CPC5 speed limit now changes "cruise control speed limit" too
  2. FR/CPC speed limit now changes "custom speed limit" too (before only "legal speed limit" was changed)
  3. ISP EIS connect (was "internal error")
  4. Do not show unused (disabled) buttons for "EEPROM B" memory operations
  5. Ignition dialog for Freightliner truck does not block further operations
  6. FR (metal case) EEPROM read/write
  7. CPC4 detection improved (some CPC4 were detected as CPC2)
  8. VW PTM parameters set
  9. EDC7UC31 FLASH write (in DC2 GPT mode) now is more stable (was frequent "error 3.5" before)
  10. Homepage when offline now displayed correctly (was always "loading" before)
  11. FFR read keys info, write speed limit, pairing, read VDF (was error 0.3)
  12. Reading DFLASH (as part of FLASH) for CPC4 added
  13. MR (KLine on pin 7) added to KAMAZ
  14. "error 0.3" at 100% during ACM/MCM FLASH write in BSL mode
  15. "internal error" during CPC4 speed limit read
  16. CPC3 operations via OBD fixed
  17. "error 3.8" during EDC17CV41 connect
  18. "Bad cable ID" during BSL EDC17CV41/EDC17CV42 connect
  19. CPC2+ diagnosis version 00004B DC memory operations (was "error 3.7")
  20. VCM speed limit on some ECUs versions returned "invalid value" before
  21. CPC diagnosis version 3C
  22. ACM/MCM BSL FLASH write (ECU did not respond after write)
  23. EHZ, ADM BSL operations (was "error 0.0" and "unavailable function" errors)
  24. FFR-EDC pairing (was "error 3.5")
  25. PTM speed limit change in some cases failed with "error 3.5" but tokens were used
  26. VCM VIN on Parameters tab was displayed truncated (last 3 digits were missed)
  27. for EDC7/EDC17 in GPT mode dump check before write was incomplete (loader was not checked) so ECU after invalid dump write can become unresponsive
  28. error "Verification did not pass" during FR immo off (via OBD)
  29. VW PTM memory operations, parameters write over OBD or DC (was "error 3.5")
  30. DC2 EIS operations ("no ignition" error)
  31. Iveco EDC7UC31 communication moved back from KLine (pin 7) to CAN (pin 6   14)
  32. for Iveco OBD connection ignition voltage is not checked on the OBD pin
  33. TCM unpair via DC (sometimes give "verification did not pass" error)
  34. MAN FFR-MS6.x pairing (was "error 3.5")
Supported new ECU versions:
  1. All possible ACM2/ACM2.1/ACM3 and MCM/MCM2/MCM2.1 are added
  2. Immo off for PTM 81.25805-7143
  3. VDF read for PTM 81.25805-7143, 81.25805-7152
  4. PTM 81.25805-7155, 81.25805-7153, 81.25805-7140
  5. Iveco EDC7UC31 version F.0.1
  6. Kamaz EDC7UC31 version 1.3.1
  7. MR2 versions supported: 30D, 31C (License MR+) 
  8. MAN EDC7C32 version 2.6
  9. Spansion S29AL016J chip support (MAN PTM 81.25805-7154; was "error 3.D" during EEPROM read)
  10. Volvo EDC7UC31 versions P520, P1090
  11. PTM 81.25805-7153 memory operations
  12. MAN EDC17CV42 FLASH writes for versions 1.5.4, 3.10.6, 3.10.7, 4.8.4, 6.6.2, 6.7.3
  13. Iveco EDC17CV41 FLASH writes for versions D.1.5, D.2.2, H.1.2
  14. MCM2.1 diagnosis version 0006D2
  15. VCM2 firmware version VCM_SW_WP6_rel6
  16. MR versions 30A, 32A
  17. EDC17CV41 (Iveco) firmware version C.7.1
  18. Immo off for PTM 81.25805-7148, 81.25805-7149, 81.25805-7150

New operations in software v6.19. Price in Tokens.

ECU name:

Operation name:

Price in tokens

ACM3 Torque limit 20
ACM3 Parameters (VIN) 5
CPC3Evo Password reset 10
EDC17CV42+PTM Pairing 100
EDC17CV42 Parameters: (tester info, item number, data record number, software number, unmachined part number, VIN, EOL info)  5
VCM2 Speed limit 20
VCM3 Speed limit 20
VCM2 Parameters (VIN, PIC) 5
VCM3 Parameters (VIN, PIC) 5
MR Unit pump ("trim") codes 2
  DDDL Backdoor password calculator 10
EMS Speed limit 40
CPC4 Restore RTC
(Remove Fault code: 61020C; 10A10: Common Powertrain Controller CPC control unit Hardware fault)

Fault codes | PLD Flash files | How to buy | General terms | Privacy policy

VEI® Truck Explorer® AutoVEI® All rights reserved. 2012-2023